Page 767 - Plastic Process Equipment, Inc

1/16 DIN TEMPERATURE CONTROL

SPECIFICATIONS & PRICES

Panel Cutout: 1.771" (45mm) sq.
4.654" Linear Input: Type L1 to L6 (Refer to Ordering Codes)
2.100" (118.2mm)
(53.3mm) 0.717" 3.937" Engineering Units Scalable, -1999 to 9999
(8.21mm) (100mm) Digital Filtering 0.1, 1.0, or 10 sec
Decimal Position Selectable, none, 1/10 or 1/100
2.100" 1.750"
(53.3mm) (44.5mm)
Control Characteristics
Setpoint Limits Limited to configured range of TC and RTD
Alarms Adjustable for high/low; selectable process
Available Inputs or deviation
Thermocouple K, J, N, R, T, S Rate 0 to 900 sec
Maximum lead resistance, 100 ohms for Reset 0 to 3600 sec
rated accuracy Cycle Time 0.2 to 120 sec
RTD Platinum, 3-wire, 100 ohms at 0°C, DIN Gain 0 to 400
curve standard (0.00385) Gain Ratio 0 to 2.0 (in 0.1 increments)
Linear Current and voltage (refer to ordering note) Control Hysteresis 1 to 100 (on/off configuration)
Spread (Output 2) 0 to 100 (above setpoint)
Ramp to Setpoint 1 to 100 minutes
Output Options Autotune Operator-initiated from front panel
#1 reverse-acting, #2 direct-acting Manual Control Operator-initiated from front panel
B & Y Relay 5 A @ 120 Vac 3 A @ 240 Vac
F 4-20 mA, 500 ohms max
S 20 Vdc pulsed General
T Solid-state relay, 120/240 Vac, zero voltage Line Voltage 115 to 230 Vac ±10%, 50/60 Hz
switched, 1A continuous, 10A surge @ 25°C 115 to 300 Vdc ±10%, (auto polarity)
(use a RC snubber when driving a Display Dual, 4-digit, 9.2mm
mechanical or mercury relay) Process: orange
Alarms Solid-state relay 1 A, 120/240 Vac @ 25°C Menu/parameter: green
Relay 5 A @ 120 Vac 3 A @ 240 Vac Power Consumption Less than 6 VA (instrument)
Weight < 8 oz (227 g)
Front Panel Rating NEMA 4X
Performance Operating Temperature 32 to 131°F (0 to 55°C)
Accuracy ±0.2% of FS, ± one digit Humidity Tolerance 90% R.H. maximum, non-condensing
Setpoint Resolution 1 count/0.1 count Memory Protection Solid-state, nonvolatile memory
Repeatability ±1.0 count Connections Input and output via barrier strip,
Temperature Stability 5µ V/°C maximum with locking terminals
TC Cold End Tracing 0.05°C/°C ambient Contacts Twin bifurcated, double-wipe
Noise Rejection Common mode > 70 dB
Series mode > 70 dB
Process Sampling 10 Hz (100 ms) 16-

Input Range Code Output 1 Output 2 Options Price Options Price
"K" TC 0 to 2460°F KF Configuration Price Configuration Price
"K" TC -18 to 1349°C KC 00=None N/C Process Value Retransmit
Code Code
"J" TC 0 to 1400°F JF Dual Alarms 60=4 to 20 mA
0=None 0=None N/C 10=Dual S.S. Relay (N.O.) 61=1 to 5Vdc $75.00
"J" TC -18 to 760°C JC S=Pulsed 20 Vdc N/C B=Relay
"N" TC 0 to 2370°F NF S=Pulsed 20 Vdc $25.00 20=FloatingTransistor $40.00 62=0 to 20 mA
B=Relay Open Collector Switch 63=0 to 5 Vdc
"N" TC -18 to 1299°C NC $25.00 T=S.S. Relay
T=S.S. Relay 21=24 Vdc drive Heater Break*
"R" TC 0 to 3200°F RF E=0-20 mA Consult
E=0-20 mA F=4-20 mA $30.00 23=Single Relay 71=10 to 60 A Factory
"R" TC -18 to 1760°C RC $30.00
F=4-20 mA Y=Relay (N.C.) Communications
"T" TC -200 to 601°F TF *Requires Current Transformer
30=RS-232 $95.00 #580E023U01.....................................$56.00
"T" TC -129 to 316°C TC
31=RS-485
"S" TC 0 to 3200°F SF Remote Setpoint
"S" TC -18 to 1760°C SC Select (w/alarm)
100 ohm RTD -328 to 1562°F PF 40=Switch Close $75.00
100 ohm RTD -200 to 850°C PC BASE PRICE 41=Switch Open
100 ohm RTD -199.8 to 449.9°F DF 42=5 volt Input
$ 230. 00 Transducer Excitation
100 ohm RTD -128.8 to 232.2°C DC
50=10 Vdc
51=12 Vdc $75.00 U L
®
52=15 Vdc
53= 5 Vdc
PLASTIC PROCESS EQUIPMENT, INC. www.ppe.com
e-mail: sales@ppe.com
E 8303 CORPORATE PARK DRIVE W 6385 MONTESSOURI STREET
A MACEDONIA, OHIO 44056-2300 E LAS VEGAS, NEVADA 89113-1186 Toll Free: USA, Canada & Mexico
S 216-367-7000 • FAX: 216-367-7022 S 702-433-6385 • FAX: 702-433-6388 800-362-0706
T TOLL FREE: 800-321-0562 T TOLL FREE: 800-258-8877 Order Fax: 800-223-8305
767