Page 221 - Plastic Process Equipment, Inc

THE SMALLER HEATED GATE CUTTER

FOR HEAT SEALED CUTS

FEATURES & SPECIFICATIONS FOR OPERATOR SAFETY A BLADE OPENING
SEPARATE GROUND LEAD IS 1" AT TIP
• 100 to 350°F Cutting Edge Temperature ATTACHED TO THE HEATER 1/2" AT BASE OF
• Lower Initial Cost SHEATH. CUTTING EDGE
• Lower Replacement Cutter Cost
• Precise Pivot for Better Blade Alignment CAUTION: ALWAYS WEAR BLADE LENGTH
15/16"
• Cutter Can be Resharpened HEAT RESISTANT GLOVES
WHEN USING A HOT
• Heat Block is Replaceable CUTTER.
• Smaller Cutting Head than Competing Models
• Uses Higher Wattage 1/4" Dia. Heaters
• Swaged-in Stainless braid lead
• Head Width 3/4" x 1/4" High HEAVY DUTY REPLACEABLE HEATER BLOCK
• Flat Back for Flush Cuts COIL SPRING IF YOU WEAR OUT THE CUTTER
• Hot Blades Cut Easier #PLC513A YOU ONLY BUY A NEW LOW
• Heat Seals Cuts COST GATE CUTTER AND
CHANGE THE PARTS
• Eliminates Cut Cracks
• Foam Insulated grips
(We suggest you wear a glove
for protection when you use
this hot cutter)

MODEL HGC-K45 #P-304-CCT FLAT BACK BLADES
Plug Only
FOAM 30° ANGLE
HEATED GATE CUTTER KIT INSULATED NON-REMOVABLE
$ 230. 00 HANDLE COVER #S-304-AB

ILLUSTRATE: Replacement
REPLACEMENT GATE CUTTER MODEL HGC-K45 Socket
MODEL HGC-45 HEATED GATE CUTTER
STAINLESS STEEL KIT WHICH INCLUDES,
ONLY BRAIDED LEADS CUTTER, HEATER
RESIST WEAR AND SOLID STATE
$ 31. 00 CONTROL BOX.
The Model HGC-K45 is a lower cost answer to trimming problems that require a heated gate Fuse Types used:
cutter. However, this cutter is not as effective or efficient as our larger Model HGC-K10 due Old Style (silver box): AGC-1
to the location of the heater blocks which are fastened directly on the cutting blades. This New Style (black box): GMA-1
permits better heat transfer, higher temperatures and thus more effective cutting. HGC-06
SOLID STATE TEMP.
CAUTION: USE HIGH TEMPERATURE GLOVES WHEN USING A PPE HEATED GATE CUTTER! CONTROL 120/60/1
PART NO. DESCRIPTION PRICE
HGC-K45 HEATED GATE CUTTER KIT W/CUTTER, HEATER ASSEMBLY, CONTROL BOX AND PAD $230.00
HGC-44 HEATED GATE CUTTER ASSEMBLY WITHOUT CONTROL BOX $83.00
HGC-45 HEATED GATE CUTTER ONLY DRILLED FOR HEATER BLOCK $31.00
CARTRIDGE HEATER ASSEMBLY WITH GROUNDED SHEATH AND PLUG 120/60/1
HGC-43 $43.20
HEATER IS 1/4" DIA. x 1-1/16" LONG x 50 WATTS, 120 VOLT, 72" STAINLESS STEEL LEADS
HGC-06 SOLID STATE TEMPERATURE CONTROL 1 AMP 120/60/1 W/6FT. GROUNDED CORD $175.00
HGC-15 3/4" I.D. HEAT SHRINK TUBING 4" LONG (1 req'd) $.72 ea
HGC-09 FOAM INSULATED HANDLE GRIP VINYL PLASTISOL (1 req'd) $1.50 ea
HGC-42 ALUMINUM HEATER BLOCK W/ALL SCREWS AND HEX KEY $10.40 ea
HGC-13 INSULATION PAD 4" x 4" x 1/4" TO REST HEATED CUTTER ON BETWEEN CUTS. $2.95
P-304-CCT 4 PIN PLUG WITH STRAIN RELIEF $4.45
S-304-AB 4 PIN SOCKET WITH ANGLE BRACKET $2.95
NOTE: This is a non-returnable product unless it's defective. It will be replaced.
PLASTIC PROCESS EQUIPMENT, INC. www.ppe.com
e-mail: sales@ppe.com
E 8303 CORPORATE PARK DRIVE W 6385 MONTESSOURI STREET
A MACEDONIA, OHIO 44056-2300 E LAS VEGAS, NEVADA 89113-1186 Toll Free: USA, Canada & Mexico
S 216-367-7000 • FAX: 216-367-7022 S 702-433-6385 • FAX: 702-433-6388 800-362-0706
T TOLL FREE: 800-321-0562 T TOLL FREE: 800-258-8877 Order Fax: 800-223-8305
221